"Three-point floor, seven-point installation", this is a common saying in the solid wood flooring industry. It can be seen that installation plays a vital role in the use of solid wood flooring. Today, furniture fans share the steps of installing solid wood flooring and precautions for installation.
Solid wood floor installation steps
1, check the ground
Solid wood floor installation sounds very difficult, but it is not. First of all, the installation of solid wood flooring must be done beforehand to check whether the ground is flat. The height of the surface of the ground should not differ by 3mm, and the ground should be dry. Neat, do not leave a little impurity, the test method is to put a few films on the floor where the floor needs to be installed, sealed, after about 12 hours, see if there is water vapor and some impurities in the film attached Above, if not, the ground is dry and clean. The floor in front of the floor should be placed at room temperature for 48 hours to ensure that the floor is adapted to the temperature and humidity of the environment. The installation will not be caused by thermal expansion and contraction, and will not adapt to the environment. .
2, start construction
The construction method of the floor installation is to adopt a tiled construction method, and the distance between the floor and some fixed objects such as the wall edge and the column should be set to a length of about 9 mm. When paving, it is necessary to ensure that each floor needs Staggered 30cm for paving, so it looks very beautiful. When paving, the floor is now covered with a floor mat of about 2mm thickness. The material is made of high-density polyethylene. The interface needs to be sealed with tape, and then a layer of 0.5mm or more is laid on the ground. The film is then reattached to more than 50 mm at the seam and finally sealed with tape. Paving should be carried out from the wall of the room. The distance between the floor and the wall is reserved for a clearance of about 9 mm. For each row, the excess part of the floor must be sawed with a saw. When paving the last row, it is very accurate to measure the width of the last row, accurately remove the excess floor, then use the hook to lay the pavement, and finally install the baseboard in the reserved place.
3, cleaning completed
The final step is of course to clean up the residue after a series of work on the floor covering and then clean the entire floor.
Extended reading: nine practical tips to buy solid wood flooring
Solid wood floor installation precautions
Who buys the floor for who to install?
Try to let the sellers who sell the floor provide paving services. Otherwise, when there is a problem in the floor in the future, the seller and the construction party will shirk their responsibilities, making the problem difficult to solve.
Ground leveling
Before installing the floor, it is best to let the manufacturer go to the door to investigate whether the ground needs to be leveled or partially leveled. Paving reinforced flooring must be leveled, while paving solid wood flooring because of the keel, unless the gap is too large, generally do not have to level. This article was originally created by Song Ye, please use WeChat search for 33 days.
Floor cleaning
Before the floor is installed, the floor of the pavement floor should be cleaned to ensure the dryness of the floor, so do not use water during the cleaning process. When the floor is installed, if there are conditions, the floor must be cut in the hallway and cleaned after completion. Because the indoor cutting of the floor is more serious to the indoor pollution, similar to the cutting of artificial stone countertops in the kitchen cabinet.
Overall trial shop
The color difference of the solid wood floor can be adjusted, and the floor with the same tone of the pattern can be placed in the living room, the aisle or the obvious place, and the slight color difference is placed under the furniture or at the corner, and the color difference is too large to be exchanged for the overall aesthetic coordination.
Laying direction
Usually the length of the floor is arranged in the direction of the room or along the light. The most used ones are 1/3 arrays, and there are also 1/2 arrays or herringbone arrangements.
nail
When laying the floor and nailing, use the special nail for the floor, preferably the nail.
installation fee
The laminate flooring is generally provided by the sales manufacturer for free installation service, and the installation of the solid wood flooring needs to pay the installation cost. The brands are slightly different. When purchasing the floor, the installation fee should be determined with the merchant. The general brand installation cost is about 50 (including the keel fee), and this cost is increasing year by year as the labor increases.
loss
Don't let the master squander the floor when you are installing it. The side of the floor is divided into yin and yang (that is, concave and convex). It is good to find a suitable use from the wood that has been scrapped, because it will always be short when it is placed on the doorway. This can effectively reduce losses.
Desk controller basic software is a PC/MAC software reminding the user to use the office desk. Allows user to control height adjustment and pre-set individual optimal sit-stand table height. Pick your personal challenge for standing at your desk and improve your health and work habits over time.
Hand controller also has many functions, such as two memory controller, metric and inch switch, overheat / overload protection, anti colony feature, soft start / stop feature, child lock and so on. There are also many types of hand controllers to choose from to meet the different requirements of customers.
Desk Controller,Office Desk Control,Standing Desk Control,Electric Desk Control,Desk Hand Remote
Suzhou Uplift Intelligent Technology Co., Ltd , https://www.uplift-system.com