[ Chinese wardrobe network ] I don't know if everyone has such an experience: when buying furniture, I am very excited, and I have chosen people to help me to go home, but the big pieces of furniture such as wardrobes , beds, etc. are very bad. Moving upstairs, sometimes the corner of the stairs is stuck, but I dare not force. According to the current situation of consumers, assembled furniture enters the market. Among them, the assembled wall wardrobe, which is very convenient for transportation, has been favored by many people.
Assembled wall wardrobe
Assembling the wall closet - installation conditions for the assembled closet
1. The structural engineering and the structural joints of the wall closet have the conditions for installing the closet and the hanging cabinet, and the indoor level has an elevation.
2. After the wall closet frame and the fan enter the field, the finished product should be placed against the wall and the ground in time. The top surface should be coated with anti-corrosion paint. The other surfaces should be painted with a base oil, then the classification should be placed, and the bottom layer should be flat and kept. Ventilation, generally should not be stored in the open air.
3. The frame and fan of the wall closet should be inspected for corners, warps, bends, and cracks before installation. If any of the above defects are found, they should be repaired and assembled. The steel frame of the hanging cabinet should be inspected for specifications, and the deformation should be corrected and then installed.
4. The frame installation of the wall closet should be carried out before plastering; the installation of the fan should be carried out after plastering.
Assembling the wall closet - installation process of the assembled closet
1. Process flow: find the line positioning → frame, rack installation → wall cabinet, partition, fulcrum installation → wall (hanging) cabinet fan installation → hardware installation
2. Find the position of the line: Use the indoor uniform elevation line before plastering, and determine the corresponding position according to the height of the wall closet and the height of the upper and lower mouth according to the design and construction drawings.
3. Frame and frame installation: The frame and frame of the wall closet should be carried out before plastering indoors. After being installed in the correct position, each nail of the two sides of the frame is nailed and nailed to the wall. The nail cap must not be exposed. . If the partition wall is an aerated concrete or a lightweight partition wall, it shall be fixed according to the structure required by the design. If the design does not require, the Φ5mm hole can be pre-drilled, the depth is 70-100mm, and the wooden wedge is pre-buried in the hole, and the glue is mixed with the cement slurry. After the hole is firmly bonded, the fixed cabinet is installed.
When using a steel cabinet, it is necessary to pre-embed the iron parts at the position where the hole fixing frame is installed, and to weld the frame parts.
When the frame and frame are fixed, the calibration, sleeve, and straightness should be corrected first, and the elevation, size, and position should be correct before fixing.
4. Installation of the partition wall fulcrum: Install the partition fulcrum strip (frame) according to the elevation position of the construction drawing and the required fulcrum structure. The fulcrum of the wooden partition is generally nailed to the wall brick, and the concrete partition is generally a truss iron or an angle bracket.
5. Assemble the wall closet cabinet fan installation:
1) According to the installation position of the fan, determine the hardware model and the direction of the split fan. Generally, the right fan in the opening direction should be the cover fan.
2) Check the size of the frame: the height of the frame should be measured at both ends; the width of the frame should be at the top, middle and bottom of the frame, and the corresponding part of the fan should be dotted.
3) According to the scribing, the frame fan will be trimmed for the first time, so that the frame and the fan are suitable for the seam. The test and the second planing line are prepared. At the same time, the position of the frame and the fan hinge groove is drawn, and the dash is avoided. Raise your head up and down.
4) Shovel and splicing page slot mounting hinge: According to the hinge position of the marking, use the flat shovel to cut out the hinge edge to close the page slot.
5) Installation: When installing, the hinge should be pressed into the hinge groove of the fan first, and the fixing screw should be tightened. The depth of the groove should be adjusted during the trial installation. Adjust the gap of the frame and the hinge on the frame. Screw one screw first, then close it. The inspection frame and the fan are flat and free of defects. After meeting the requirements, tighten all the screws.
Wood screws should be nailed into the full length 1/3, screwed into 2/3. If the frame or fan is yellow bud or other hardwood, the hinge mounting screws should be positioned and the hole diameter is 0.9 times the diameter of the wood screw, and the depth of the eye is 2/3 length of the screw.
6) Install the split fan: firstly measure the size of the frame and the fan, determine the middle seam and the depth of the cut, and then plan the groove after the line is used. When the test is suitable, install the left fan first and then install the cover fan.
6. Hardware installation: The variety, specification and quantity of hardware are installed according to the design requirements. Pay attention to the choice of position when installing. If there is no specific size, the operation will be carried out according to the technical basis. Generally, the sample should be installed first, and after installation, it will be installed in a large area.
The assembled wall closet is not only easy to carry, but also easy to install. Besides the professional master to help install, you can also try to be self-reliant, which is a wardrobe that is very suitable for the masses. Although the assembled wardrobe is assembled, the overall is very solid, so everyone can rest assured. When you buy a wall-mounted wardrobe, you should first look at the size and quality of the finished product, and then choose a wall-mounted wardrobe that suits your home!
The dual motor Standing Desk is 1.5-2.5mm thick cold rolled steel plate with high mechanical strength, smooth surface and uniform thickness.
Adopt the quality motor of which listed company to ensure that the lifting is not stuck, the lifting speed is 32mm / s.the sound under no load is less than 45dB, quiet and noiseless, and does not affect other people's office.The motor has strong power, stable power output and stable load bearing of 80kg, which can meet the needs of daily entertainment and office desktop storage. Colleagues can cooperate with the function of resistance retreat and power-off protection to ensure the safety of lifting. The power in standby mode is only 0.1W, energy saving and environmental protection.
Dual Motor Standing Desk,Standing Desk Dual Motor, Electric Standing Desk Dual Motor, Sit Stand Desk Dual Motor,Electric Sit Stand Desk Dual Motor
Suzhou Uplift Intelligent Technology Co., Ltd , https://www.uplifting-desk.com